Exam program: Occupational health and safety
IAE-EXAM-HS · version 1.0
Sections, format, sample tasks and scoring rubric of the IAE written exam in the field "Occupational health and safety".
01. Who is the exam for?
For occupational health and safety specialists and engineers, heads of occupational and industrial safety departments, industrial hygienists, safety coordinators on construction sites and in manufacturing, and area supervisors responsible for the safety of work. Admission requires a bachelor's degree or higher and at least 3 years of experience in the field (without a degree, at least 5 years). The exam tests calculations and decisions based on data on work, measurements and incidents: risk assessment and the choice of protective measures, injury rates and the investigation of causes, noise and hazardous substances in workplace air, isolating equipment from energy sources during repair, permits for hazardous work and work at height, justifying the cost of measures and reporting to management after an incident. Knowledge of the laws and codes of a particular country by heart is not required: the exposure limits, thresholds and requirements needed for the solution are given in the task. Construction and energy project management is covered by the "Engineering projects: construction and energy" program, statistical quality control and Lean Six Sigma projects by the "Quality management and Lean Six Sigma" program, employee relations and HR processes by the "Human resources management" program, and compliance and anti-money laundering by the "Compliance and anti-money laundering (AML)" program.
02. Format
- 5 questions, one per section, 10 minutes each.
- 2 cases of 25 minutes from two different sections: risk and hazard assessment, safety metrics and incident investigation, industrial hygiene, process and work safety. The cases require calculations with the candidate's own data: the risk level on the matrix given in the task before and after measures, the frequency and severity of injuries per hours worked, noise exposure over a shift as a percentage of the allowed exposure and the time-weighted average noise level, the time-weighted average exposure to a substance and its share of the limit given in the task, the ventilation airflow, the clearance below a worker using a fall arrest system, evacuation time, the cost of measures and the payback period.
- 1 question about the project from the candidate's questionnaire, 10 minutes.
- Up to 2 hours in total, in one sitting. Pasting is disabled, and each candidate gets their own case data.
03. Sections and weights
- Risk and hazard assessment - 20 %: hazard identification by type (mechanical, electrical, chemical and physical agents, falls from height, ergonomic loads) and by job step, the risk matrix: the severity score multiplied by the likelihood score, on the scales and with the risk level bands given in the task, the hierarchy of controls (elimination of the hazard, substitution with a less hazardous substance, machine or method, engineering controls, administrative controls and personal protective equipment; measures higher on the list are more reliable because they depend less on worker behavior), residual risk (the risk that remains after the measures are taken) and the decision whether it is acceptable under the criteria given in the task, job safety analysis (JSA: the job is divided into steps, and for each step the hazards, the measures and the person responsible are recorded), review of the assessment after a change in the work and after an incident.
- Safety metrics and incident investigation - 20 %: LTIR (lost time injury rate: the number of injuries with lost work time multiplied by 200,000 and divided by the number of hours worked; 100 workers working 40 hours a week for 50 weeks work 200,000 hours in a year) and TRIR (total recordable injury rate: all injuries that must be recorded under the rules given in the task, per the same 200,000 hours), the same rates per 1,000,000 hours, injury severity as lost workdays per 200,000 hours, comparing periods and areas with different numbers of hours worked, leading indicators (actions before an injury: training, observations of work, hazards removed, reports of events without injury) and lagging indicators (injuries and lost days), incident investigation: facts, witness interviews, the "5 whys" method (the question "why?" is asked about each cause found until a removable cause in the organization of work is found) and the cause tree (a diagram that gives for each event all the conditions without which it would not have happened), corrective actions with an owner, a deadline and a check of the result.
- Industrial hygiene - 20 %: noise: the level in dBA (the sound level in decibels adjusted for how hearing responds to different frequencies), the noise dose (the sum of the time at each noise level divided by the allowed time at that level under the rule given in the task; a dose of 100 % equals the allowed exposure for a shift) and the 8-hour time-weighted average noise level, noise reduction by hearing protection with the correction given in the task, chemical substances: TWA (time-weighted average exposure: the sum of the concentration multiplied by the length of each interval, divided by 8 hours) and its share of the limit given in the task, the sum of the shares of the limits for several substances if the task says so, ventilation: air changes per hour (how many room volumes the ventilation supplies in an hour) and the airflow needed to dilute a substance with the data given in the task, ergonomics: lifting and carrying loads, repetitive movements and working posture assessed by the method given in the task, personal protective equipment: choosing a respirator by how many times the exposure exceeds the limit and by the protection factor given in the task, choosing hearing protection and gloves with the data given, fit checks.
- Process and work safety - 20 %: lockout and tagout of energy sources (LOTO: isolating equipment from all energy sources, including pressure and stored energy, a personal lock and tag of each worker on the isolating device, a check that no energy remains before work starts), machine guards and safety devices, permits to work for high-risk work (a written authorization for a specific job that lists the hazards, measures and people responsible and has a period of validity), including hot work, work at height: the choice between guardrails, a restraint system and a fall arrest system, calculating the clearance below the worker in a fall with the data given in the task, the rescue plan, work in confined spaces (tanks, wells and other places with limited entry and exit where there may be too little oxygen or a hazardous gas may build up): air testing before entry and during the work, an attendant at the entrance, the rescue plan, fire safety and evacuation: evacuation time by the length of the routes and the capacity of the exits given in the task, management of change (assessing the hazards before a change to equipment, a substance, a process, a schedule or the workforce, and a check before start-up), process safety with hazardous substances at the level of principles: accident scenarios and protective barriers.
- Professional practice - 20 %: the occupational health and safety management system: policy and objectives, management review of results, internal audit against the requirements given in the task, the audit sample and the share of nonconformities, the corrective action plan, worker training and involvement: a training plan based on the risks of workplaces, checking the result of training, worker participation in risk assessment, reports of events without injury and the right of a worker to stop unsafe work, work with contractors: prequalification by the indicators given in the task, requirements in the contract, supervision on site, justifying the cost of measures: the cost of a measure, the direct and indirect costs of an injury given in the task and the payback period, the report to management after an incident: what happened, the causes, what was done, what is proposed, what it costs and by when, honest reporting: recording all incidents without underreporting and without pressure on workers who report injuries, the candidate's own project.
04. Sample tasks
Question. Last year a plant had an average of 360 workers, who worked 720,000 hours; this year, after a new shift was opened, it had 420 workers and 840,000 hours, of which 120,000 hours were worked on the new shift. Last year there were 8 recordable injuries, 4 of them with lost work time, and 60 lost workdays in total. This year there were 9 recordable injuries, 4 of them with lost work time, and 96 lost days in total, of which 52 days came from one injury (a fracture in a fall off a portable ladder); 4 of this year's 9 injuries happened on the new shift. Calculate the TRIR, the LTIR and the severity rate (lost days per 200,000 hours) for both years and the LTIR per 1,000,000 hours for this year. Explain why there were more injuries but the rates went down, what changed in severity and what the severity rate would be without the fracture. Compare the injury rate on the new shift and on the other shifts, and answer whether these data are enough to say that safety at the plant has improved.
Case. A stamping shop has 12 presses and 80 workers, and 40,000 hours were worked in the quarter. In the quarter there were 3 hand injuries with lost work time (14, 21 and 45 lost days); in the 4 previous quarters, with 160,000 hours worked, there was 1 such injury (12 lost days). Two injuries happened on presses No. 3 and No. 7 when operators reached into the die area to remove jammed blanks by hand; on both presses the safety light curtain had been bypassed with a jumper. The third injury happened during setup of press No. 7: another worker started the press, and there was no lock on the start control. According to the log, there were 310 jammed blanks in the quarter, 220 of them on presses No. 3 and No. 7. In 40 observations of press setup and repair, a personal lock with a check that no energy remained was used in 22 cases, a lock without the check in 10 and no lock in 8; the shop has 6 personal locks for 18 setters. Operators receive a bonus for meeting the shift target. Noise for the operators of presses No. 3 and No. 7: 94 dBA for 4 hours of the shift, 88 dBA for 2 hours, 80 dBA for 2 hours; under the rule given in the task, the allowed time at 85 dBA is 8 hours, and it is halved for every 3 dBA increase in the level. One lost-time injury costs the company 35,000 on average (payments, replacing the worker, press downtime). Proposed measures: repair of the feed and dies of presses No. 3 and No. 7 (30,000; the setters estimate 80 % fewer jams on these presses); light curtains that cannot be switched off on all 12 presses and tools for removing blanks (78,000); personal locks and tags for all 18 setters, a lockout procedure and training (10,000); cut-resistant gloves (8,000 a year); noise enclosures on presses No. 3 and No. 7 that reduce the level by 10 dBA (24,000); earmuffs rated at 25 dB, of which half is counted (3,000 a year). The budget for measures this year is 125,000. Find the causes of the injuries from the data, and calculate the LTIR and the severity rate for the quarter and for the 4 previous quarters. Calculate the noise dose and the time-weighted average level over a shift now, with enclosures and with earmuffs. Sort the measures by the hierarchy of controls, choose measures within the budget and calculate the payback period under two assumptions about the number of injuries without the measures: as in this quarter and as the average over 5 quarters. Write a message to the plant director: what happened in figures, the causes, what was done at once, what is proposed, what it costs and how the result will be checked.
The figures and circumstances of the cases are different for each candidate.
05. Scoring rubric
Each task is scored on four criteria, and the total is converted to 100 points taking the section weights into account.
- Correctness of the solution - 40 %.
- Reasoning behind decisions - 25 %.
- Risks and constraints - 20 %.
- Clarity of the answer - 15 %: structure and precise wording. Grammar and style do not reduce the score if the meaning is clear.
06. Result
- Pass mark - 70 of 100.
- Result in 5 business days. Those who pass receive an IAE Certified Professional certificate in the field "Occupational health and safety", valid for 3 years; scores by section are in a separate report.
- The certificate confirms that the candidate passed the written exam under this program. It is not a license or an accreditation and does not replace the occupational health and safety certificates of other organizations or the training and knowledge tests required by the law of a particular country. Employers and authorities make hiring and other decisions about the candidate under their own rules.
- Retake 30 days after the first failed attempt and 60 days after the second, with no more than 3 attempts in 12 months.
- Full terms: the Exam terms page.
- The Credentialing Council reviews the program at least once a year.
07. What is not covered?
- The IAE exam is not an exam of other organizations that certify occupational health and safety specialists, is not affiliated with them and does not replace their exams. The topics and tasks of the IAE exam do not repeat the syllabi of those exams. The names of certifications and organizations belong to their owners.
- Knowledge of the laws, codes and rules of a particular country by heart is not required. The exposure limits for noise and hazardous substances, thresholds, deadlines and requirements needed for the solution are given in the task as company rules. The exam does not test the legal assessment of compliance with the laws of a particular country or questions of the liability of the employer and its officers.
- Occupational medicine and environmental regulation are not covered: medical examinations, the diagnosis of occupational diseases and decisions on whether a worker is medically fit for the job, permits for emissions and discharges and reporting on them. If medical information is needed for the solution, it is given in the task as a doctor's conclusion; in this exam, ventilation and hazardous substances are considered for workplace air.
- Construction and energy project management (schedules, cost, contracts and handover) is covered by the "Engineering projects: construction and energy" program. The design of buildings and building systems, including ventilation and fire protection, is not covered: the building and equipment specifications for calculations are given in the task. In this exam, the safety of construction work is assessed by the risks to workers, without the project schedule and cost.
- Statistical process control and Lean Six Sigma improvement projects are covered by the "Quality management and Lean Six Sigma" program. In this exam, internal audit and corrective actions belong to the occupational health and safety management system, and the incident and measurement data are given in the task.
- Employee relations and HR processes, including recruitment, pay, disciplinary matters and workplace investigations, are covered by the "Human resources management" program. In this exam, worker training and involvement are assessed as safety measures, and investigations deal with incidents and their causes.
- Compliance programs, anti-money laundering and sanctions screening are covered by the "Compliance and anti-money laundering (AML)" program. In this exam, audits and checks of compliance cover occupational health and safety and industrial safety, and the requirements are given in the task.
- Work in particular incident recording and risk assessment software and the setup of measuring instruments are not tested. Measurement results and other data needed for the solution are given in the task, and calculations are done by hand or on a calculator.
08. Preparation
- The practice exam runs in the same interface: 2 questions from different sections, a 15-minute case and a project question.
- Review the calculations: the risk level on the matrix given in the task before and after measures and the risk reduction under the hierarchy of controls; LTIR and TRIR per 200,000 and per 1,000,000 hours, severity by lost days, comparing periods and areas with different numbers of hours worked, the share of corrective actions completed on time; the noise dose and the time-weighted average noise level over a shift, noise reduction by hearing protection under the rule given in the task, the TWA of a substance and its share of the limit, the sum of the shares for several substances, air changes per hour and airflow; the clearance below a worker using a fall arrest system, evacuation time by the length of the routes and the capacity of the exits; the cost of an injury, the cost of measures and the payback period, the share of nonconformities in an audit sample.
- Formulas are given in the task when needed, as are exposure limits, the allowed time at each noise level and the scales of the risk matrix. A calculator is enough for the calculations, and reference materials may be used.
- Answer by the points of the task: the method or formula, the calculation on your own figures, the decision, risks and what needs to be checked. List measures in the order of the hierarchy of controls and name an owner and a deadline for each. Pasting is disabled, so the answer is typed.
- Prepare the project description for the questionnaire: your role, the plant or site and its size (the number of workers and hours worked per year), the task, indicators before and after (for example, the injury rate or the share of workplaces where noise is above the limit), the decisions taken, the result in figures. Do not include confidential employer data (internal incident reports, inspection results, figures the company does not publish) or information about injured workers and their health: the result can be given as a percentage of the starting level. The project question is based on this description.
- Text from AI services and help from other people are not allowed.
Exam
Book the exam
The questionnaire takes 15 minutes. Admission decision in 1 business day.

